act

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/P5_automation_arduino_status_submodule.ino

@@ -1,4 +1,5 @@
 #define HAS_u8g2
+//#define HAS_PCF8591
 
 
 #include <Arduino.h>
@@ -6,6 +7,9 @@
 #include <SPI.h>
 #include <Wire.h>
 
+#include "PCF8591_init.h"
+
+
 //SSD1306
 #include <Adafruit_SSD1306.h>
 #include <Adafruit_GFX.h>
@@ -53,6 +57,7 @@ int test_pwm_pin = 9;
 
  void setup(void) {
     Serial.begin (115200);
+    #include "PCF8591_setup.h"
 
     #if defined(HAS_Adafruit_SSD1306)
     //SSD1306
@@ -77,6 +82,7 @@ int test_pwm_pin = 9;
   pinMode(in_test_status_p5_temp_3, INPUT_PULLUP);
   pinMode(in_test_status_p5_temp_4, INPUT_PULLUP);
 
+  pinMode(in_test_status_p5_current, INPUT_PULLUP);
 
 
 
@@ -92,49 +98,58 @@ int test_pwm_pin = 9;
         #include "i2c_scanner_setup.h"
         i2c_scanner();
    #endif
+   
+    
+  byte count = 0;
+  pinMode(13,OUTPUT); 
+  digitalWrite(13,HIGH);
+  Wire.begin();
+  for (byte i = 1; i < 120; i++)
+  {
+    Wire.beginTransmission (i);
+    if (Wire.endTransmission () == 0)
+      {
+      Serial.print ("Found address: ");
+      Serial.print (i, DEC);
+      Serial.print (" (0x");
+      Serial.print (i, HEX);
+      Serial.println (")");
+      count++;
+      delay (1); 
+      } 
+  } 
+  Serial.println ("Done.");
+  Serial.print ("Found ");
+  Serial.print (count, DEC);
+  Serial.println (" device(s).");
+  
+  
 }
 
 //#include "scan_ports.c"
 
-void status_pin(STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_T pin) {
-    int state = digitalRead(pin );
-           if(state == HIGH) {
-              // Good
-              #if defined(HAS_u8g2)
-             // u8g2.setCursor (3, 20);
-              u8g2.print (" +");
-              u8g2.sendBuffer();         // transfer internal memory to the display
-              #endif
-           } else {
-              // Bad
-              #if defined(HAS_u8g2)
-          //    u8g2.setCursor (3, 20);
-               u8g2.print (" -");
-               u8g2.sendBuffer();         // transfer internal memory to the display
-             #endif
-            }
-}
-
-
 void loop(void) {
    
-    /*
-    
-     delay(2);
-      digitalWrite(test_pwm_pin, HIGH);
-        delay(2);
-      digitalWrite(test_pwm_pin, LOW);
-    */
-
-    //scan_ports();
-    delay(2000);
-
-    /*
-    int out_test_status_p5_bus_1_port_6_red_led_pin = 5 ;
-    int  in_test_status_p5_bus_1_port_7_red_buttopn_pin = 6 ;
-    int out_test_status_p5_bus_1_port_8_green_led_pin = 7 ;
-    int  in_test_status_p5_bus_1_port_9_black_buttopn_pin = 8 ;
+  
+    delay(STATUS_SYSTEM_LATENCY_MAIN_LOOP_A);
+       /* 
+         Serial.print("pcf8591.voltageRead: ");
+         float ana0V = pcf8591.voltageRead(AIN0);
+	       Serial.print(ana0V);
+         Serial.print(" , ");
+       	float ana1V = pcf8591.voltageRead(AIN1);
+       	Serial.print(ana1V);
+            Serial.print(" , ");
+       	float ana2V = pcf8591.voltageRead(AIN2);
+       	Serial.print(ana2V);
+       	 Serial.print(" , ");
+       	float ana3V = pcf8591.voltageRead(AIN3);
+       	Serial.println(ana3V);       	
+                   delay(1000);
     */
+  
+  
+  
     #if defined(HAS_u8g2)
     u8g2.clearBuffer();        
     u8g2.setFont(u8g2_font_amstrad_cpc_extended_8f);  // choose a suitable font
@@ -147,33 +162,39 @@ void loop(void) {
      display.display();
      #endif
     
-    status_pin(out_test_status_p5_bus_1_port_6_red_led_pin);
+    //status_pin(out_test_status_p5_bus_1_port_6_red_led_pin);
     
     STATUS_PHYS_PIN_INPUT_INT_ERROR_F(STATUS_SYSTEM_CONDITION_A,in_test_status_p5_bus_1_port_7_red_buttopn_pin);
     //status_pin(in_test_status_p5_bus_1_port_7_red_buttopn_pin);
     
-    status_pin(out_test_status_p5_bus_1_port_8_green_led_pin);
+   // status_pin(out_test_status_p5_bus_1_port_8_green_led_pin);
     STATUS_PHYS_PIN_INPUT_INT_OK_F(STATUS_SYSTEM_CONDITION_A, in_test_status_p5_bus_1_port_9_black_buttopn_pin);
     //status_pin(in_test_status_p5_bus_1_port_9_black_buttopn_pin);
-      #if defined(HAS_u8g2)
+      
+    STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_temp_1, in_test_status_p5_temp_1_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
+    STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_temp_2, in_test_status_p5_temp_2_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
+   #if defined(HAS_u8g2)
         u8g2.setCursor(0,20);
        //  u8g2.setFont(u8g2_font_m2icon_5_tf);  // choose a suitable font
       #endif
-    STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_temp_1, in_test_status_p5_temp_1_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
-    STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_temp_2, in_test_status_p5_temp_2_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
-      #if defined(HAS_u8g2)
-        u8g2.setCursor(0,30);
-       #endif
+     
     STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_temp_3,  in_test_status_p5_temp_3_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
     STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_temp_4,  in_test_status_p5_temp_4_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
+    STATUS_PHYS_PIN_INPUT_RANGE_F(in_test_status_p5_current,  in_test_status_p5_curren_RANGE_A,  STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
+
 
+    #if defined(HAS_u8g2)
+        u8g2.setCursor(0,30);
+       #endif
     STATUS_SYSTEM_CONDITION_F(STATUS_SYSTEM_CONDITION_A, STATUS_SYSTEM_CONDITION_ERROR_COUNT_A);
     STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_F(STATUS_SYSTEM_CONDITION_A, out_test_status_p5_bus_1_port_8_green_led_pin );
     STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_ERROR_F(STATUS_SYSTEM_CONDITION_A, out_test_status_p5_bus_1_port_6_red_led_pin );
        #if defined(HAS_u8g2)
        // u8g2.setCursor(0,40);
         //String STATUS_SYSTEM_CONDITION_A_S  ;
+        u8g2.print("[");
           u8g2.print(String(STATUS_SYSTEM_CONDITION_A, BIN));
+          u8g2.print("]");
           u8g2.sendBuffer(); 
        #endif
        

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/PCF8591_init.h

@@ -0,0 +1,9 @@
+#if defined(HAS_PCF8591)
+
+#include "Arduino.h"
+#include "PCF8591.h"
+#define PCF8591_I2C_ADDRESS 0x48
+
+PCF8591 pcf8591(PCF8591_I2C_ADDRESS);
+
+#endif

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/PCF8591_setup.h

@@ -0,0 +1,3 @@
+#if defined(HAS_PCF8591)
+    pcf8591.begin();
+#endif

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/___CONFIG/config_status.h

@@ -12,6 +12,11 @@ STATUS_PHYS_PIN_INPUT_T in_test_status_p5_temp_3 = A2 ;
 STATUS_PHYS_PIN_INPUT_T in_test_status_p5_temp_4 = A3 ;
     STATUS_PHYS_PIN_INPUT_RANGE_T in_test_status_p5_temp_4_RANGE_A = { 0 , 2000 } ;
 
+STATUS_PHYS_PIN_INPUT_T in_test_status_p5_current = A6 ;
+        STATUS_PHYS_PIN_INPUT_RANGE_T in_test_status_p5_curren_RANGE_A = { 0 , 1000 } ;
+
+
+
 STATUS_PHYS_PIN_OUTPUT_INT_T out_test_status_p5_bus_1_port_2_i2c_5v_int_err_pin = 3 ; 
 STATUS_PHYS_PIN_OUTPUT_INT_T out_test_status_p5_bus_1_port_4_i2c_3v_int_err_pin = 4 ; 
 STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_ERROR_T out_test_status_p5_bus_1_port_6_red_led_pin = 5 ;
@@ -19,3 +24,4 @@ STATUS_PHYS_PIN_INPUT_INT_ERROR_T  in_test_status_p5_bus_1_port_7_red_buttopn_pi
 STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_T out_test_status_p5_bus_1_port_8_green_led_pin = 7 ;
 STATUS_PHYS_PIN_INPUT_INT_OK_T  in_test_status_p5_bus_1_port_9_black_buttopn_pin = 8 ;
 
+STATUS_SYSTEM_LATENCY_MAIN_LOOP_T STATUS_SYSTEM_LATENCY_MAIN_LOOP_A = 300 ;

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/___main/__main_int_init.h

@@ -0,0 +1,5 @@
+
+//#include <avr/interrupt.h>
+//#include <avr/sleep.h>
+ //attachPinChangeInterrupt(MYPIN1, quicfunc, FALLING);
+//todo

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/___main/__main_struct_status.h

@@ -1,5 +1,8 @@
 #include <Arduino.h>
 
+typedef int STATUS_SYSTEM_LATENCY_T ; //TO Set some timers
+typedef STATUS_SYSTEM_LATENCY_T STATUS_SYSTEM_LATENCY_MAIN_LOOP_T ;
+
 typedef byte STATUS_SYSTEM_CONDITION_T;  //status of system
 const STATUS_SYSTEM_CONDITION_T STATUS_SYSTEM_CONDITION_INIT_A                     = B00000001 ; 
 const STATUS_SYSTEM_CONDITION_T STATUS_SYSTEM_CONDITION_UNKNOWN_A                  = B00000010 ; 

SE/stuff/P5_Automation_can-dev-res-working-1930/___SUBMODULES___/P5_automation_arduino_status_submodule/___main/__main_struct_status_func.h

@@ -81,8 +81,16 @@ void STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_F(STATUS_SYSTEM_CONDITION_T &STA
    STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_T STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_A) {
    if(STATUS_SYSTEM_CONDITION_A & STATUS_SYSTEM_CONDITION_OK_A) {
       digitalWrite(STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_A, HIGH);
+      #if defined(HAS_u8g2)
+         u8g2.print (" +");
+        // u8g2.sendBuffer();         // transfer internal memory to the display
+      #endif
    } else {
       digitalWrite(STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_OK_A, LOW);
+      #if defined(HAS_u8g2)
+         u8g2.print (" -");
+       //  u8g2.sendBuffer();         // transfer internal memory to the display
+      #endif
    }
 
 }
@@ -95,8 +103,16 @@ void STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_ERROR_F(STATUS_SYSTEM_CONDITION_T &
       digitalWrite(STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_ERROR_A, HIGH);
    } else if(STATUS_SYSTEM_CONDITION_A & STATUS_SYSTEM_CONDITION_ERROR_SET_INT_REQ_A) {
       digitalWrite(STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_ERROR_A, HIGH);   
+       #if defined(HAS_u8g2)
+         u8g2.print (" +");
+      //   u8g2.sendBuffer();         // transfer internal memory to the display
+      #endif
    } else {
       digitalWrite(STATUS_PHYS_PIN_OUTPUT_SYSTEM_CONDITION_ERROR_A, LOW);
+      #if defined(HAS_u8g2)
+         u8g2.print (" -");
+      //   u8g2.sendBuffer();         // transfer internal memory to the display
+      #endif
    }
 
 }
@@ -109,7 +125,7 @@ void STATUS_PHYS_PIN_INPUT_INT_OK_F(STATUS_SYSTEM_CONDITION_T &STATUS_SYSTEM_CON
               #if defined(HAS_u8g2)
              // u8g2.setCursor (3, 20);
               u8g2.print (" +");
-              u8g2.sendBuffer();         // transfer internal memory to the display
+            //  u8g2.sendBuffer();         // transfer internal memory to the display
               #endif
            } else {
               // Bad
@@ -131,7 +147,7 @@ void STATUS_PHYS_PIN_INPUT_INT_OK_F(STATUS_SYSTEM_CONDITION_T &STATUS_SYSTEM_CON
               #if defined(HAS_u8g2)
           //    u8g2.setCursor (3, 20);
                u8g2.print (" -");
-               u8g2.sendBuffer();         // transfer internal memory to the display
+             //  u8g2.sendBuffer();         // transfer internal memory to the display
              #endif
             }
 }
@@ -146,7 +162,7 @@ void STATUS_PHYS_PIN_INPUT_INT_ERROR_F(STATUS_SYSTEM_CONDITION_T &STATUS_SYSTEM_
               #if defined(HAS_u8g2)
              // u8g2.setCursor (3, 20);
               u8g2.print (" +");
-              u8g2.sendBuffer();         // transfer internal memory to the display
+            //  u8g2.sendBuffer();         // transfer internal memory to the display
               #endif
            } else {
               // Bad
@@ -175,7 +191,7 @@ void STATUS_PHYS_PIN_INPUT_INT_ERROR_F(STATUS_SYSTEM_CONDITION_T &STATUS_SYSTEM_
               #if defined(HAS_u8g2)
           //    u8g2.setCursor (3, 20);
                u8g2.print (" -");
-               u8g2.sendBuffer();         // transfer internal memory to the display
+             //  u8g2.sendBuffer();         // transfer internal memory to the display
              #endif
             }
 }